Error code canon mp145, MP150, MP160 (Download Service Tool V-1050)
Error code canon mp145, MP150, MP160
E2-2 = No paper or paper priter can not rally (can because dirty roll)
E3-3 = Paper hours
E4 = No ink / cartridge
E5-5 = ink cartridges are not installed or installed incorrectly cartirdge (not compatibel)
E8 = absorber full, or Platen waste ink absorber full reset Mita
E9 = connection to digital camera / video camera does not support
E14 = Ink cartridges whose destination are wrong
E15 = color Catridge experiencing run out
E16 - Black Catridge experiencing run out
E17-E19 = problems on the scan head alignment sheet
E22 = Carriage error
E23 = Paper feed error
E24 = Purge unit error (the cleaning head)
E25 = ASF (cam) sensor error
E26 = Internal temperature rise error
E27 = ink absorber full or Platen waste ink absorber full> reset with toolsnya
E28 = Ink cartridge temperature rise error -
E29 = EEPROM error
E33 = Paper feed position error
E35 15 = USB Host VBUD overcurrent error - USB
E37 17 = Abnormal motor driver
E40 20 = Other hardware error
E42 22 = Scanner error
here's how to reset the waste ink counter (E16 error):
1. Turn off the printer (power cable is still tercolok), press and hold the STOP / RESET then press the ON / OFF
2. Hold down the ON / OFF, press the STOP / RESET 2x
3. Release both buttons and the printer will enter SERVICE MODE
4. Printer will be charging
5. Once the printer is done charging, press the STOP / RESET 4x. (Waste ink counter reset)
6. Each time the button STOP / RESET is pressed, the lights ON / OFF will turn green and orange colors
7. Turn off the printer and disconnect the cable POWER
8. Turn the printer back.
The number of the Reset:
pressing button
LED Function Remarks
0 time Green Power off
1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset
5) Unplug the power cable. (For MP145 / MP150)
6) Turn Off Power. (For MP160)
CANON MP145 PRINTER INK PROBLEM FULL Absorber (E 2 7 error message)
1. Turn off the printer (press the on / off)
2. press the stop / reset, do not acquitted
3. press again the power button, the power led lights up (not removable).
4. Last stop button / reset, press the stop button again reset 2 times.
5. after the power switch on / off
6. wait until the main LED (led display) show the number 0 on PANEL PRINTER, after pointing the figure 0 immediately press the stop / reset 4 times
7. press the power button 1 time (paper roller rotates, power led blinking)
8.Tunggu up led stop blinking and the printer stand-by (if there is not a direct response to just turn off your printer)
9. turn off your printer.
10. you turn on the printer again.
To reset Canon Printer MP type can also be done by using the Service Tool or MP tool.download hear disini
How to use this September:
1. Turn off the printer (press the on / off)
2. press the stop / reset, do not acquitted
3. press again the power button, the power led lights up (not removable).
4. Last stop button / reset, press the stop button again reset 2 times.
5. after the power switch on / off
6. wait until the main LED (led display) show the number 0 on PANEL PRINTER, after pointing the figure 0, then go to file Service Tool is you download.
7.setelah you extract or open files with WinRAR Service Tool or winzip, open file V1050.exe Service tool will then appear under the picture Sep at.
9. For no.5 select PLAY & PLATTERN
10.Press no.1 if you want to reset the Ink Counter, or
11.Press no.2 if you want to reset the EPROM
* Service MP tool or tools would only work if your printer in conditions of service mode (display O)
For Error 3 trial in check around the pump removal ink gear2 no problem E3 kalaya this cause is whether the stand of loose gear.
Run out to a good Cartride black or color .... enough with pressing the resume around 5secon or to display a reminder on your monitor screen Hila